KODAK AZ1000 - Revision history

Joosteto: /* WiFi protocol */

2021-07-21T19:30:20Z

WiFi protocol

2021-07-21T19:25:46Z

WiFi protocol

2021-07-21T19:20:33Z

2021-07-07T18:44:10Z

Created page with "[http://tech.komputilo.org/images/b/b9/Az1000-manual-en.pdf User manual]"

New page

[http://tech.komputilo.org/images/b/b9/Az1000-manual-en.pdf User manual]

← Older revision		Revision as of 19:30, 21 July 2021
Line 20:		Line 20:
	Notice that the camera is picky about the DOS line ending (\r\n), and doesn't accept just plain \n. This works on Unix:		Notice that the camera is picky about the DOS line ending (\r\n), and doesn't accept just plain \n. This works on Unix:

−	printf 'GET /DCIM/100KODAK/100_0180.JPG HTTP/1.0\r\n\r\n ~~HTTP/1.1~~' \| nc 10.0.0.46 80	+	printf 'GET /DCIM/100KODAK/100_0180.JPG HTTP/1.0\r\n\r\n' \| nc 10.0.0.46 80
		+
		+	Transfer isn't very fast: about 0.7 MByte/s.

@@ Line 4: / Line 4: @@
 When turning the function dial to "WiFi", the camera gives the user two options:
-* Access point (camera becomes access point)
+* Station: connect camera to existing access point
-When choosing "Station" the camera scans available access points, and allows the user to choose one. Next the WiFi password can be entered, and then the camera sits silent.
+When choosing "Station" the camera scans the available access points, and allows the user to choose one. Next the WiFi password can be entered, and then the camera sits silent.
 From here the user somehow has to figure out the IP number received from the DHCP server (log in to your router, use nmap, etc).
 I haven't figured out how to get a directory listing, but the following will get image 100_0180.JPG from the camera (if it exists):

← Older revision		Revision as of 19:20, 21 July 2021
Line 1:		Line 1:
	[http://tech.komputilo.org/images/b/b9/Az1000-manual-en.pdf User manual]		[http://tech.komputilo.org/images/b/b9/Az1000-manual-en.pdf User manual]
		+
		+	=WiFi protocol=
		+	When turning the function dial to "WiFi", the camera gives the user two options:
		+
		+	* Station (connect camera to existing access point)
		+	* Access point (camera becomes access point)
		+
		+	When choosing "Station" the camera scans available access points, and allows the user to choose one. Next the WiFi password can be entered, and then the camera sits silent.
		+
		+	From here the user somehow has to figure out the IP number received from the DHCP server (log in to your router, use nmap, etc).
		+
		+	I haven't figured out how to get a directory listing, but the following will get image 100_0180.JPG from the camera (if it exists):
		+
		+	GET /DCIM/100KODAK/100_0180.JPG HTTP/1.0
		+
		+	Notice that the camera is picky about the DOS line ending (\r\n), and doesn't accept just plain \n. This works on Unix:
		+
		+	printf 'GET /DCIM/100KODAK/100_0180.JPG HTTP/1.0\r\n\r\n HTTP/1.1' \| nc 10.0.0.46 80