Papilio - Revision history

Joosteto: /* Components */

2013-12-11T21:41:59Z

Components

2013-11-29T19:25:15Z

Compiling xc3prog

2013-05-30T07:52:00Z

2013-05-04T22:03:40Z

Errors when programming using low-powerd devices

2013-05-04T22:02:08Z

2013-04-25T23:14:24Z

2013-04-21T22:12:35Z

Hello World VHDL

2013-04-21T22:00:51Z

Hello World VHDL

2013-04-20T17:25:42Z

Components

2013-04-20T17:23:55Z

Components

@@ Line 124: / Line 124: @@
 * Power Converter: AMS 1117 \n 5.0 HT ????
 * 6-pin IC close to FTDI: 1TET, in schematic: 93LC46B
-* 8-pin flash IC: ?, in schematic: FLASH-SPI-25XXSMD1 (FLASH-SPI-25XX), maybe [http://www.amictechnology.com/pdf/A25L512.pdf this one]
+* 8-pin flash IC: ?, in schematic: FLASH-SPI-25XXSMD1 (FLASH-SPI-25XX), maybe [http://www.amictechnology.com/pdf/A25L512.pdf this one], Xilinx info on the chip: [http://www.xilinx.com/support/documentation/application_notes/xapp951.pdf Configuring Xilinx FPGAs with SPI Serial Flash]
 =See Also=

@@ Line 53: / Line 53: @@
 =Compiling xc3prog=
 Tested on Ubuntu 13.04 (beta) and raspberry Pi (raspbian)
  <nowiki>

@@ Line 1: / Line 1: @@
-* Papilio [http://papilio.cc/index.php?n=Papilio.Reference Reference page]
+* Papilio [http://papilio.cc/index.php?n=Papilio.Reference Reference page], more info [http://gadgetforge.gadgetfactory.net/gf/project/butterfly_one/ gadgetforce]
 * Xilinx [http://gadgetforge.gadgetfactory.net/gf/download/frsrelease/134/412/BPC3003_2.03%2B.ucf constraints.ucf] file.
 * Papilio [http://papilio.cc/index.php?n=Playground.PapilioPinouts Pinouts]

@@ Line 96: / Line 96: @@
 =Errors when programming using low-powerd devices=
-When using my Raspberry Pi to program papilio, these errors appear when the papilio board needs to give too mutch power to other devices, for instance the [[DX TM1638 Display]]:
+When using my Raspberry Pi to program papilio, these errors appear when the papilio board needs to give too much power to other devices, for instance the [[DX TM1638 Display]]:
  <nowiki>$ xc3sprog -c papilio  /tmp/$f -v
 design_top.bit                                            100%  277KB 277.2KB/s   00:00
@@ Line 111: / Line 111: @@
 Could not open FTDI device (using libftdi): device not found
 Unable to access FTDI device with either libftdi or FTD2XX</nowiki>
 =Components=

@@ Line 94: / Line 94: @@
 * [http://www.xilinx.com/support/documentation/data_sheets/ds312.pdf#page=51 drawings with CLKFB]
 * [http://duteela.et.tudelft.nl/~elca/XilinxTutor/documents/xapp462.pdf#page=6 DCM Primitive]
 =Components=

@@ Line 49: / Line 49: @@
 Or, via my raspberry pi:
  f=LEDtest.bit ; scp $f pi:/tmp; ssh pi "sudo /home/joostje/debian/papilio/Papilio-Loader/xc3sprog/trunk/build/xc3sprog -c papilio  /tmp/$f -v"
 =Compiling xc3prog=

@@ Line 46: / Line 46: @@
 #or use FTDI & FLASH to make non-volatile:
 sudo ./xc3sprog -c papilio -I../bscan_spi/bscan_spi_xc3s500e_papilio.bit ~/VHDL/LEDTest/LEDtest.bit  -v -R</nowiki>
 =Compiling xc3prog=